Why Understanding Plumbing Basics is Essential When Installing a Bathtub
Why Understanding Plumbing Basics is Essential When Installing a Bathtub
Blog Article
Just how do you feel when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a tub isn't precisely rocket science, but it does need solid plumbing, carpentry, and often, tiling skills. Changing an old bathtub with a brand-new one is likewise a reasonably hard project. If the old bathtub is easily obtainable, the task can move quickly; if you need to open a wall to get rid of the old tub and position the new bathtub, the job is a lot harder. In either case, the task is within a residence handyman's abilities, although you will certainly need an assistant to leave the old bathtub as well as embeded in the new one. Make sure you have actually qualified yourself for the job and also fit attempting it. Instead of employing a specialist to take control of a halfway-completed project, it is better to consider utilizing one before you begin. Possibilities are you might require an expert plumber to make tube connections.
This short article will assist you set up a new bathtub in your washroom if you have actually currently acquired a brand-new tub and do not need to alter the setup of your previous water system pipelines.
Your devices and also product list must make up the following:
Planning for the Installment
To start with, the supporting frame provided with the bath should be fitted (if called for) according to the supplier's guidelines. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps unit to prevent strain on the bathtub.
Fit the flexible faucet connectors to the bottom of both taps using 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you use every one of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its final setting.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you must do is detach the water system. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The procedure of getting rid of the existing taps can be quite troublesome because of the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipes. When the supply pipes have been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from transforming during this process. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any old securing compound.
Before moving on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the bath tub in the required position. The wooden boards are helpful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny points.
The next objective is to ensure that the tub is leveled all round. This can be accomplished by inspecting the level and also changing the feet on the bath tub up until the spirit level reviews degree.
To set up faucets, fit the bottom of the outermost flexible tap port to the ideal supply pipe by making a compression join; then do the same for the various other faucet.
Activate the water supply and examine all joints as well as brand-new pipework for leaks and also tighten them if essential. Fill the bath tub as well as additionally check the overflow outlet as well as the typical electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the maker's instruction manual. Tiling as well as securing around the bath tub must wait up until the bathtub has been used at the very least once as this will certainly resolve it right into its final placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin ensuring that the washing machines are in place between the tap as well as the sink. Secure the faucet in place with the maker given backnut. As soon as the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular tap ports. The former type must be connected to the tap ends first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bathroom meets the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to split a rigid seal, creating the water to penetrate the wall surface between the bathroom and the tiling, bring about issues with moisture as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and cartridges, as well as are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill up the tub with water before securing, to allow for the movement experienced when the bathtub remains in use. The sealant can fracture fairly early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently offered on the market. It is recommended to fit the floor tiles using waterproof or water-proof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that write up on A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the search engines. In case you appreciated our post please don't forget to share it. Thanks for your time. Kindly stop by our website back soon.
Prioritize plumbing safety. Report this page